Difference between revisions of "HandPunch Network Configuration Guide"

From sbv.wiki
Jump to: navigation, search
Line 1: Line 1:
−
{{#urlget:Contact|User}},
+
== {{#urlget:HandPunch|HandPunch}} Network Configuration Guide ==
  
−
We can also have a page where we send users to when you know the IP information for the clock
+
These are the instructions for entering the network information into the HandPunch.
  
−
blah blah blah...
+
# From the main screen ('''ENTER ID'''), press Clear then Enter.
−
 
+
# If you see '''ENTER PASSWORD''' in the display then there are no supervisors currently enrolled in the HandPunch. Skip to step 6.
−
Enter ''{{#urlget:IpAddress|192.168.001.099}}'' then press Enter
+
# You should see a star symbol ('''*''') on the bottom line of the display. If you do not see the '''*''' then go back to step 1.
−
 
+
−
Then enter ''{{#urlget:GatewayAddress|192.168.001.001}}'' and press enter
+
−
 
+
−
Finally enter {{#urlget:HostBits|24}} ..........
+
−
 
+
−
**NOT FINAL JUST A RUDIMENTARY LIST OF INSTRUCTIONS**
+
−
 
+
−
# From the main screen (ENTER ID), press Clear then Enter. (If you see ENTER PASSWORD in the display then there are no users currently enrolled in the HandPunch. Skip to step 6)
+
−
# You should be a star symbol (*) on the bottom line of the display. If you do not then go back to step #1.
+
 
# Enter in your Clock ID and press Enter.
 
# Enter in your Clock ID and press Enter.
−
# The displays shows PLACE HAND. Place your hand.
+
# The displays shows '''PLACE HAND'''. Place your hand.
−
# You should see ENTER PASSWORD in the display.
+
# You will  see '''ENTER PASSWORD''' in the display.
−
# Press 2 then press Enter.
+
# Press 2 then Enter.
−
# Scroll through the menu options by selecting the “No” key (*) and go to the Set Serial Option and select “Yes”
+
# Press No (*) until you see '''SET SERIAL'''. Before you press Yes (#) you must be ready to start entering the IP Address on the next step. Press Yes (#).
−
# At this point you will enter the IP address immediately. (You need to enter the IP address right away because if you wait too long it will move to the next option. For Example, if you IP address was 192.168.1.50, you                        need to enter the complete address. You would do it like this: 192.168.001.050)
+
# Enter ''{{#urlget:IpAddress|192.168.001.099}}''. Before you press Yes (#) you must be ready to start entering the Gateway Address on the next step. Press Yes (#).
−
# Once the IP address is entered, select the “Yes” key and it will ask you to enter the Gateway. Enter the gateway the same way as you would the IP address. (For example, a gateway of 192.168.1.1 would be typed out as 192.168.001.001)
+
# Enter ''{{#urlget:GatewayAddress|192.168.001.001}}''.  Before you press Yes (#) you must be ready to enter the Host Bits on the next step. Press Yes (#).
−
# Enter Host bits
+
# Enter ''{{#urlget:HostBits|24}}''. Press Yes (#) twice.
−
# Baud rate should be 9600
+
# Press Clear until you are back to the main screen ('''ENTER ID''').
−
# Push clear a few times to get back to the main screen of “enter ID”
+

Revision as of 16:24, 30 December 2016

HandPunch Network Configuration Guide

These are the instructions for entering the network information into the HandPunch.

  1. From the main screen (ENTER ID), press Clear then Enter.
  2. If you see ENTER PASSWORD in the display then there are no supervisors currently enrolled in the HandPunch. Skip to step 6.
  3. You should see a star symbol (*) on the bottom line of the display. If you do not see the * then go back to step 1.
  4. Enter in your Clock ID and press Enter.
  5. The displays shows PLACE HAND. Place your hand.
  6. You will see ENTER PASSWORD in the display.
  7. Press 2 then Enter.
  8. Press No (*) until you see SET SERIAL. Before you press Yes (#) you must be ready to start entering the IP Address on the next step. Press Yes (#).
  9. Enter 192.168.001.099. Before you press Yes (#) you must be ready to start entering the Gateway Address on the next step. Press Yes (#).
  10. Enter 192.168.001.001. Before you press Yes (#) you must be ready to enter the Host Bits on the next step. Press Yes (#).
  11. Enter 24. Press Yes (#) twice.
  12. Press Clear until you are back to the main screen (ENTER ID).
Retrieved from "http://sbv.wiki/index.php?title=HandPunch_Network_Configuration_Guide&oldid=1472"